- 您现在的位置：买卖IC网 > Sheet目录324 > ER2-4M-90 (TechTools)EMULATOR EPROM ECONOROM II 4MEG
Turn on the Target’s Power
The emulator is powered from the target. The target power must always be on to access the emulator from
either the target or the HOST side. When target power is applied, the emulator’s POWER LED should
glow steadily. This LED is powered DIRECTLY by the target’s power.
If the POWER LED does not glow, immediately turn
off target power and correct the problem before re-
applying power!
The only possible causes for the LED not to light are:
- target cable plugged in backwards or incompletely,
- insufficient target power,
- incorrect target cable adapters (wrong PLCC adapter, etc.),
- incorrect target socket wiring,
- bad target interface cable or
- a damaged emulator.
Connect the Download Cable
Select an unused PRINTER port on your PC. Remove any “dongles”, security keys, printer switch boxes
or extension cables from the port. Plug the supplied download cable directly into the selected printer port.
Plug the other end of the cable into Econo ROM II’s “IN” port.
PLUGGING Econo ROM II INTO A SERIAL PORT
WILL DAMAGE THE EMULATOR!
Run self-test
Run ER2TEST.EXE. This file is located on the ERII Loaders Diskette. This self test will verify proper
operation of the parallel port and all Econo ROM II functions except the target interface buffers. If any of
these tests fail, refer to the troubleshooting section for assistance. If the troubleshooting section does not
resolve the problem, call our technical support people for help.
If you are using multiple Econo ROM IIs, test each one individually. The test program is designed to test
only one emulator at a time. After all emulators have been tested, you may daisy-chain them together to
access them together or individually from a single printer port. Multiple units are daisy-chained by
connecting the “OUT” connector from the first unit to the “IN” connector of the second unit. Additional
units are added in the same manner. The modular download cable can be used as a daisy-chain cable by
removing the DB-25 adapter.
Econo ROM II User’s Manual
4
Copyright ? 1996, TechTools
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ER3-8M
EMULATOR EPROM ECONOROM III 8MEG
ESF2424
FRAME SWING ECLIPSE 19.25X19"
ESF3024
FRAME SWING ECLIPSE 24.5X19"
ESF3624
FRAME SWING ECLIPSE 29.75X19"
ESP1212
PANEL STEEL SWING 12X12" WHT
ESP1612
PANEL STEEL SWING 16X12" WHT
ESP1616
PANEL STEEL SWING 16X16" WHT
ESP1620
PANEL STEEL SWING 16X20" WHT
相关代理商/技术参数
ER25
制造商:SPC Multicomp 功能描述:EXTENSION RING 25MM PK 10 制造商:Datak Corporation 功能描述:PC Drafting Or Transfer Accessories
ER250-104X
制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:DC Filter Capacitors
ER250-254
制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:DC Filter Capacitors
ER250-503
制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:DC Filter Capacitors
ER250-504
制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:DC Filter Capacitors
ER-2643
功能描述:烙铁 SOLDERING TIP
RoHS:否 制造商:Weller 产品:Soldering Stations 类型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大温度:+ 850 F 电缆类型:US Cord Included
ER26500
制造商:EVE 功能描述:BATTERY LITHIUM 3.6V C 制造商:EVE 功能描述:BATTERY, LITHIUM, 3.6V, C
ER26500M
制造商:EVE 功能描述:BATTERY LITHIUM 3.6V C 制造商:EVE 功能描述:BATTERY, LITHIUM, 3.6V, C